产品类别
称重测力传感器
压力传感器及变送器
速度及加速度传感器
料/液位计
位移传感器
扭矩传感器
温湿度传感器,变送器
显示控制仪表
记录仪
整列机
测力系统
微粒子检测仪
激光器
流量传感器/开关
陀螺仪
引伸计
频闪仪
变送器/放大器
变频器
编码器
试验机
数据采集器
角度传感器
声级计
振动计
多通道分析仪
流量计
电子衡器
实验室设备
水分分析仪
质量流量计
测试分析系统
模块型仪表
静电纺丝机
高速数据采集卡
Tinius Olsen测试设备
试验机
信号调理器
Sirius数据采集系统
切割设备
三维扫描仪
示波器
水听器
功率放大器
安全保持器
温度计监视器
振动增幅器
人像表面温度热像仪
温度检查器
红外线 辐射温度仪
红外多分析仪
FC评价试验装置
电缆
加速度传感器
碳气溶胶组分在线分析系统
黑碳仪
接线盒
显示器
隔离器/转换器
探头
低温冰箱
超低温冰箱
液氮罐
实验炉
PF5-024EM电流传感器
品牌:美国 OSI
型号:PF5
类型:相位角传感器
产品描述/DESCRIPTION
PF5型提供的直流输出与交流电力系统电压和电流之间的相位差成线性比例,双向输出的极性表示超前或滞后条件。
平衡负载条件在三相系统中是必要的,偏离正弦波条件会导致所有传感器的不准确,因为角度测量基于零交叉点之间的时间差。
The model PF5 provides a dc output which is linearily proportional to the phase angle difference between voltage and current of an ac power system. The polarity of the bidirectional output indicates leading or lagging conditions.
Balanced load conditions are necessary in three-phase systems.Deviation from sine wave conditions leads to inaccuracies with all transducers since angle measurement is based on the time difference between zero crossings.
特征/FEATURES
? PF5型的双向输出与输入信号的0°至60°超前或滞后相位角成正比
? 超前相位角导致负输出信号
? 滞后相位角会产生正输出信号
? The bidirectional output of the model PF5 is directly proportional to the 0° to 60°leading or lagging phase angle of the input signal.
? A leading phase angle results in a negative output signal.
? A lagging phase angle results in a positive output signal.
应用/APPLICATIONS
? 提供了计算功率因数的准确方法,PF=COSΦ
? Provides an accurate means for calculating power factor,PF =COSΦ
参数
电流输入 |
1.0-20.0Aac |
电压输入 |
410-550Vac |
输出 |
0-10Vdc,0-1mAdc,4-20mAdc,4-12-20mAdc |
系统配置 |
1?2W、3?3W或3?4W |
准确性 |
±0.5%跨度 |
频率 |
50-60Hz |
测量 |
交流电 |
一相二线型号
电压输入 (VL-L) |
电流输入 (Aac) |
标准输出型号PF5 |
|||
0-1mAdc* |
0-10Vdc* |
4-20mAdc** |
4/12/20mAdc |
||
95-135 |
0.2 to 5.0 |
001A |
001C |
001E |
001EM |
0.3 to 10.0 |
010A |
010C |
010E |
010EM |
|
1.0 to 20.0 |
019A |
019C |
019E |
019EM |
|
200-300 |
0.2 to 5.0 |
002A |
002C |
002E |
002EM |
0.3 to 10.0 |
011A |
011C |
011E |
011EM |
|
1.0 to 20.0 |
020A |
020C |
020E |
020EM |
|
410-550 |
0.2 to 5.0 |
003A |
003C |
003E |
003EM |
0.3 to 10.0 |
012A |
012C |
012E |
012EM |
|
1.0 to 20.0 |
021A |
021C |
021E |
021EM |
三相、三线或三相、四线型号
电压输入 (VL-L) |
电流输入 (Aac) |
标准输出型号PF5 |
|||
0-1mAdc* |
0-10Vdc* |
4-20mAdc** |
4/12/20mAdc |
||
95-135 |
0.2 to 5.0 |
004A |
004C |
004E |
004EM |
0.3 to 10.0 |
013A |
013C |
013E |
013EM |
|
1.0 to 20.0 |
022A |
022C |
022E |
022EM |
|
200-300 |
0.2 to 5.0 |
005A |
005C |
005E |
005EM |
0.3 to 10.0 |
014A |
014C |
014E |
014EM |
|
1.0 to 20.0 |
023A |
023C |
023E |
023EM |
|
410-550 |
0.2 to 5.0 |
006A |
006C |
006E |
006EM |
0.3 to 10.0 |
015A |
015C |
015E |
015EM |
|
1.0 to 20.0 |
024A |
024C |
024E |
024EM |
*表示自供电装置,所有其他型号需要85-135Vac仪器电源。
**4-20mA型号,仅用于滞后功率因数。(单向输出)
规格
输入INPUT |
||||
电流 |
1.0-20.0Aac |
|||
电压 |
410-550Vac |
|||
频率范围 |
50-60Hz |
|||
负重 |
||||
电压 |
2.0VA |
|||
电流 |
0.4VA |
|||
过载(连续) |
||||
电压 |
135Vac范围 |
175Vac |
||
300Vac范围 |
350Vac |
|||
550Vac范围 |
600Vac |
|||
电流 |
5Aac范围 |
10Aac |
||
10Aac范围 |
20Aac |
|||
20Aac范围 |
30Aac |
|||
仪表功率INSTRUMENT POWER |
||||
“A”和“C”型号 |
自动供电 |
|||
“E”、“EM”型号 |
85-135Vac,50-400Hz,3.5VA |
|||
“-22”选项 |
230Vac±15%,50/60Hz |
|||
介电测试DIELECTRIC TEST |
||||
输入/输出/案例 |
1500Vac |
|||
输出OUTPUT |
||||
跨度 |
(电流单位:参考电压单位:伏特) |
+60°- 0~60° |
||
电流引线电压 |
负输出 |
|||
电流滞后于电压 |
正输出 |
|||
加载 |
“A”型号 |
0-10kΩ |
||
“C”型号 |
2kΩ,最小值 |
|||
“E”和“EM”型号 |
0-500Ω |
|||
响应时间(至90%) |
400毫秒 |
|||
现场可调校准 |
±10% |
|||
精确ACCURACY |
±0.5%量程 |
|||
温度TEMPERATURE |
||||
工作范围 |
-20℃~60℃ |
|||
温度效应 |
±0.5%F.S. |
外壳尺寸
连接图
安装说明:正确安装PF5型相位角传感器至关重要,必须严格遵循上面所示的连接图,如果应用需要使用电流互感器,要确保极性正确,因为与所示连接的任何偏差都将导致满标度输出信号锁定。
安装/操作/保修/INSTALLATION / OPERATION / WARRANTY
安装说明/INSTALLATION INSTRUCTIONS
1.只能由合格的电工进行安装!
2.在进行任何电气连接之前,确保电气服务已断开。
3.支路保护按国家和地方规范要求设置检查机构的报告。
4.按要求布线,并按照本表和装置上的接线图固定到端子上。
5.传感器适合安装在600Vac线路上。
6.为防止与带电电路接触,当安装在裸母线上时,要求传感器安装在需要使用工具进入的外壳中。当安装在绝缘电缆上时不需要第二个外壳的电缆。
1. Installation should be performed by qualifi ed electricians only!
2. Make sure electrical service is disconnected before making any electrical connections.
3. Branch circuit protection is required to be provided in accordance with the National and Local codes of the inspection authority.
4. Route wires as required and secure to terminals per connection diagram on this sheet and on the unit.
5. Transducers are suitable for installation on 600Vac lines.
6. To prevent contact with live circuits, when installed on a bare bus bar, the transducer is required to be mounted in an enclosure that requires the use of a tool for access. When installed on an insulated cable this second enclosure is not required.
操作说明/OPERATING INSTRUCTIONS
1.本装置适用于海拔2000米以下的室内使用。
2.根据安装类别(过电压)II,污染等级2的瞬态过电压。
3.如果需要清洁外表面,则应断电所有供应服务(两个测量和仪表电源电路),并用软刷刷洗或用低压空气吹扫。使用适当的眼部保护。不适合清洗软管。
4.最高相对湿度80%,温度最高31?C,线性下降至50% 40℃时的相对湿度。
5.最大工作温度范围为-20°C至60°C。
1. This unit is intended for indoor use at altitudes up to 2000 meters.
2. Transient overvoltages according to Installation Category (overvoltage) II, Pollution Degree 2.
3. If cleaning of the exterior surface is necessary, de-energize all services of supply (both measuring and instrument power circuits) and brush with a soft brush or blow off with low-pressure air. Use appropriate eye protection. Not suitable for hose-down cleaning.
4. Maximum relative humidity 80 percent for temperatures up to 31?C decreasing linearly to 50 percent relative humidity at 40?C.
5. Maximum operating temperature range is -20°C to 60°C.